Shower Door Bottom Seal Manufacturer and Supplier
GoldRays is a China-based manufacturer and B2B supplier of bottom shower door seals, shower door sweeps and custom sealing profiles. We work with shower enclosure brands, importers, distributors and OEM/ODM buyers that need an existing profile matched or a new requirement reviewed.
A bottom seal is fitted at the lower edge of a shower door or screen to support water control around the gap below the glass. The correct profile depends on more than the glass thickness. Door movement, lower gap, attachment method, lip direction, adjacent tray or threshold and the wet-facing side all affect selection.
Send the model reference when known. Otherwise, provide a physical sample, dimensioned cross-section or clear photographs of the installed seal and enclosure. GoldRays can compare the information with an existing profile or review an OEM/ODM requirement.
Buyers comparing the wider range can visit the GoldRays product directory or the shower screen seal supplier page.
How to Select a Bottom Shower Door Seal
Select from the complete enclosure geometry, not a front-view photograph alone.
| Buyer situation | Recommended review route | Information to provide |
|---|---|---|
| Replacing a seal with a known GoldRays reference | Existing-model check | Model number, glass thickness, required length and photos of the installed position |
| Replacing an unmarked or discontinued seal | Profile matching | Physical sample or dimensioned cross-section, glass thickness, lower gap and full enclosure photos |
| Developing a new shower door or screen | Application review | Door movement, glass arrangement, lower gap, tray or threshold details and target function |
| No current profile matches the geometry | Custom-profile review | Dimensioned drawing, critical dimensions, attachment method, material preference and project requirements |
| A curved or unusual lower edge is involved | Geometry-specific review | Screen drawing, curve information, installed orientation, sample or cross-section and required length |
Final specifications, model suitability and availability are confirmed after the supplied information is reviewed.
Existing Bottom Shower Door Seal Models
The current GoldRays page lists the following bottom-seal references: 007G, 009, 009A, 009A1, 009A2, 009B, 009B1, 009C, 009D, 009B3, 009D1, 009D5, 009F, 009F1, 009F2 and 005C.
Each model block has a published glass-thickness table with reference dimensions labelled “a” and “b.” Retain those tables with their corresponding model blocks. Read the table together with the correct model drawing; do not select a profile from the numbers alone or assume that similar values mean an identical cross-section. Confirm the intended orientation, fitting area and application with GoldRays before approval.
| Glass | a | b |
|---|---|---|
| 6mm | 7 or 15 | 10 |
| 8mm | 8 or 15 | 10 |
| 10mm | 15 | 10 |
| Glass | a | b |
|---|---|---|
| 6mm | 10 | 10 |
| 8mm | 11 | 10 |
| 10mm | 11 | 10 |
| 12mm | 12 | 10 |
| Glass | a | b |
|---|---|---|
| 6mm | 11 | 8 |
| 8mm | 11 | 10 |
| 10mm | 12 | 10 |
| 12mm | 16 | 12 |
| Glass | a | b |
|---|---|---|
| 6mm | 11 | 8 |
| 8mm | 11 | 10 |
| 10mm | 12 | 10 |
| 12mm | 16 | 12 |
| Glass | a | b |
|---|---|---|
| 6mm | 12,17,23 | 10 |
| 8mm | 12,17,23 | 10 |
| 10mm | 12,35 | 10 |
| 12mm | 12 | 12 |
| Glass | a | b |
|---|---|---|
| 6mm | 8 | 7 |
| 8mm | 8 | 8 |
| 10mm | 9 | 9 |
| 12mm | 9.5 | 10 |
| Glass | a | b |
|---|---|---|
| 6mm | 8 | 13 |
| 8mm | 8 | 13 |
| 10mm | 9 | 13 |
| 12mm | 10 | 13 |
| Glass | a | b |
|---|---|---|
| 6mm | 8 | 13 |
| 8mm | 8 | 13 |
| 10mm | 9 | 13 |
| 12mm | 10 | 13 |
| Glass | a | b |
|---|---|---|
| 6mm | 12 | N |
| 8mm | 14 | N |
| 10mm | 15 | N |
| Glass | a | b |
|---|---|---|
| 4-6mm | 25 | 16 |
| 8-10mm | 38 | 17 |
| Glass | a | b |
|---|---|---|
| 6mm | 22 | N |
| 8mm | 22 | N |
| 10mm | 22 | N |
| Glass | a | b |
|---|---|---|
| 8mm | 18 | 14 |
| 10mm | 18 | 14 |
| 12-12.6mm | 18 | 14 |
| Glass | a | b |
|---|---|---|
| 8mm | 6 | 12 |
| Glass | a | b |
|---|---|---|
| 6mm | 11 | 11 |
| Glass | a | b |
|---|---|---|
| 10mm | 8 | 10 |
| Glass | a | b |
|---|---|---|
| 6mm | 15 | N |
| 10mm | 18 | N |
Existing Profile Match or Drawing/Sample Review?
Check an existing profile first when the buyer has an intact seal, known model or complete cross-section. A model name alone is insufficient when the enclosure, glass thickness or lower gap has changed.
Send a drawing or sample when the original model is unknown, damaged or no existing model appears to match. Similar-looking bottom seals can have different fitting and lip geometry.
If a suitable standard profile cannot be confirmed, GoldRays can review a custom requirement. See custom shower door seal profiles for the information used in an OEM/ODM and extrusion review. Buyers working with a bath-mounted screen can also review the bath screen seal manufacturer page.
Bottom Seal Buyer Checklist
Include the available information with an enquiry:
- Known GoldRays model number or the buyer’s current product reference.
- A dimensioned profile cross-section, technical drawing or physical sample.
- Clear close-up photographs of the profile from both ends.
- A photograph showing the seal in its installed position.
- Glass thickness and the measured lower gap.
- Door or panel type and direction of movement.
- Seal orientation and the wet-facing side.
- Tray, threshold or adjacent-surface details below the glass.
- Required profile length and any curve or unusual geometry.
- Material preference, if the project specifies one.
- Branding and export-packaging requirements, when applicable.
- Destination market and any documents that must be reviewed for the project.
Before removing an old seal, mark its top, bottom and wet-facing side. Protect the complete cross-section of any sample.
OEM/ODM Support for Bottom Seals and Sweeps
GoldRays supports existing-profile matching and custom-profile review. The broader range includes clear PVC, polycarbonate, magnetic, bottom and specialty profiles. Material and construction are confirmed per enquiry rather than inferred from appearance.
A controlled review normally follows these steps:
- Define the enclosure. Record the glass arrangement, door movement, lower gap, adjacent surface and seal position.
- Review the reference. Compare the buyer’s model, sample or drawing with relevant existing profiles.
- Clarify the specification. Confirm cross-section, key dimensions, orientation, material, length and project requirements in writing.
- Evaluate the proposed option. Check a sample or proposed profile in the actual enclosure or a representative assembly.
- Approve the complete system. Confirm fit, movement, contact points and water-management behaviour in the intended installation.
Branding and export packaging can be included in an OEM/ODM review. Provide the files and packaging brief with the technical specification.
Fit and Water-Control Considerations
A bottom shower door seal is one part of an enclosure system. Its performance depends on the profile fit, lower gap, door alignment, glass and hardware tolerances, tray or threshold geometry and installation direction. A profile should not obstruct normal door movement or create an unintended contact point.
Evaluate the finished enclosure in its intended configuration. Do not assume that a model used on one glass thickness, gap or door arrangement will suit another. For related closures, review magnetic shower door seals; for other geometries, visit standard shower seal profiles.
Frequently Asked Questions
Is GoldRays a bottom shower door seal manufacturer?
Yes. GoldRays is a China-based manufacturer and B2B supplier of shower door seals and custom sealing profiles, including bottom seals and sweeps. Product suitability and specifications are confirmed for each project.
Which bottom-seal models are shown on this page?
The page currently lists 007G, 009, 009A, 009A1, 009A2, 009B, 009B1, 009C, 009D, 009B3, 009D1, 009D5, 009F, 009F1, 009F2 and 005C. Availability and the correct use of each model should be confirmed with GoldRays.
Can GoldRays identify a replacement from a photograph?
Photographs help show the installed position, but a photograph alone may not show the complete cross-section. Send the original sample or a dimensioned drawing where possible, together with the glass thickness, lower gap and orientation.
Which glass thickness should I choose from the model tables?
Use the existing model table only with the corresponding verified drawing and application information. The glass thickness is one selection factor; the cross-section, fitting method, lower gap and lip direction must also match.
Can you review a custom bottom shower door seal?
Yes. If no existing profile is suitable, GoldRays can review a buyer-supplied drawing, sample and OEM/ODM brief. Final material, dimensions, tooling route and commercial terms are confirmed for the individual project.
Will a bottom seal make a shower enclosure completely watertight?
No individual profile should be treated as a guarantee of complete water containment. Results depend on the finished enclosure, including alignment, gaps, hardware, tray or threshold geometry and installation. Evaluate the proposed seal in the intended system.
How do I request a technical review or quotation?
Email goldrays@showerdoorseal.org with the application, model or sample, drawing, glass thickness, lower gap, required length, photos, destination market and expected volume. You can also use the GoldRays contact page.
Request a Bottom Seal Review
Send your model reference, drawing or sample information to goldrays@showerdoorseal.org. State whether the enquiry is for an existing-profile match, a replacement programme or an OEM/ODM project. GoldRays will review the supplied details and confirm the next technical step.
